;========================= GSD file: CTLS076D.GSD =====================
;
;DEVICE NAME:       P-CPATTLS
;DEVICE REVISION:   V1.0
;VENDOR NAME:       EL-O-Matic
;GSD REVISION DATE: 28-Apr-2003
;
;======================================================================
#Profibus_DP
GSD_Revision        = 3
Vendor_Name         = "EL-O-Matic"
Model_Name          = "P-CPATTLS EL-O-MATIC"    
Revision            = "1.0"
Ident_Number        = 0x076D 
Protocol_Ident      = 0
Station_Type        = 0
FMS_supp            = 0
Hardware_Release    = "1.0"
Software_Release    = "1.0"
Bitmap_Device       = "CTLS76D"
31.25_supp          = 1
45.45_supp          = 1
93.75_supp          = 1
MaxTsdr_31.25       = 100
MaxTsdr_45.45       = 250
MaxTsdr_93.75       = 1000
Redundancy          = 0
Repeater_Ctrl_Sig   = 0
24V_Pins            = 0
Freeze_Mode_supp    = 1
Sync_Mode_supp      = 1
Set_Slave_Add_supp  = 1
Min_Slave_Intervall = 250
Fail_Safe           = 1
Modular_Station     = 1
Max_Module          = 10                    
Max_Input_Len       = 100                   
Max_Output_Len      = 100                   
Max_Data_Len        = 200                   
Slave_Family        = 12                    
Max_Diag_Data_Len   = 14
Max_User_Prm_Data_Len = 3
Ext_User_Prm_Data_Const(0) = 0x00, 0x00, 0x00

;----------- Description of extended DP features: ---------------------
;
;DPV1_Slave = 1
;C2_Read_Write_supp      = 1
;C2_Max_Data_Len         = 128
;C2_Read_Write_required  = 1
;C2_Max_Count_Channels   = 2
;Max_Initiate_PDU_Length = 52
;C2_Response_Timeout     = 4000
;DPV1_Data_Types         = 0

;----------- Description of device related diagnosis: ---------------------

Unit_Diag_Bit(16)   = "- ERROR APPEARS"
Unit_Diag_Bit(17)   = "Error disappears"
Unit_Diag_Bit(24)   = "No communication with FieldQ"
Unit_Diag_Bit(28)   = "EEPROM integrity test failed"
Unit_Diag_Bit(30)   = "- DEVICE NOT INITIALIZED"
Unit_Diag_Bit(31)   = "Self calibration failed"
Unit_Diag_Bit(32)   = "Zero point error"
Unit_Diag_Bit(39)   = "Ident_Number violation"
Unit_Diag_Bit(37)   = "Maintenance required"
Unit_Diag_Bit(55)   = "- EXTENSION AVAILABLE"
;------------------------------------------------------------------------------

;Modules for Discrete Output

Module    = "SP_D"                     0xA1
1
EndModule

Module    = "SP_D+RB_D"                0xC1,0x81,0x81,0x83
2
EndModule

Module    = "SP_D+CB_D"                0xC1,0x81,0x82,0x92
3
EndModule

Module    = "SP_D+RB_D+CB_D"           0xC1,0x81,0x84,0x93
4
EndModule

; Modules for modulating output

Module = "Setpoint modulating"         0x81,0x81,0x00
5
EndModule

Module = "SP+RB modulating"            0xC1,0x81,0x81,0x01
6
EndModule

Module = "SP modulating + CB"          0xC1,0x81,0x82,0x02
7
EndModule

Module = "SP+RB modulating + CB"       0xC1,0x81,0x84,0x03
8
EndModule

Module = "RB positioning"              0x41,0x81,0x30
9
EndModule

; Special modules

Module = "FIELDQ status2 (local op status)" 0x41,0x00,0x10
10
EndModule

Module = "Control type (in & out)"     0xC1,0x00,0x00,0x11
11
EndModule

Module = "Temperature (degrees)"       0x41,0x00,0x12
12
EndModule

Module = "Temperature (fahrenheit)"    0x41,0x00,0x13
13
EndModule

Module = "AI1"                         0x41,0x81,0x14
14
EndModule

Module = "AI2"                         0x41,0x81,0x15
15
EndModule

Module = "Cycle time open & close"     0x41,0x83,0x20
16
EndModule

Module = "Break time open & close"     0x41,0x83,0x21
17
EndModule

Module = "Counter opened"              0x41,0x81,0x22
18
EndModule

Module = "Counter closed"              0x41,0x81,0x23
19
EndModule

Module = "Travel count"                0x41,0x83,0x24
20
EndModule

Module = "Travel count limit (read)"   0x41,0x83,0x25
21
EndModule

Module = "Actuator recognition"        0x81,0x80,0x26
22
EndModule

Module = "Init cmd + Init status"      0xC1,0x00,0x00,0x27
23
EndModule