; =============================
; GSD-File Gateway PROFIBUS-DP
; JUMO IMAGO 500
; Release 22.07.2002
; =============================
;
;
#Profibus_DP
GSD_Revision = 2                               ;extended GSD-file is supported
;                                              ;according to PNO directrive of 14.12.95
Vendor_Name = "MK Juchheim"                    ;name of the manufacturer
Model_Name = "IMAGO 500 JUMO"                         ;name of the DP-instrument
Revision = "Ausgabestand 2.0"                  ;actual edition of the DP-instrument
Ident_Number = 0x0629                          ;exact type designation of the DP-instrument
Protocol_Ident = 0                             ;protocol characteristica PROFIBUS-DP
Station_Type = 0                               ;DP-Slave
FMS_supp = 0                                   ;DP-instrument only
Hardware_Release = "1.00"                      ;actual edition of the hardware
Software_Release = "2.00"                      ;actual edition of the software
;                                              ;the following baudrates are supported
9.6_supp = 1                                   ;   9.6  kBaud
19.2_supp = 1                                  ;  19.2  kBaud
;                                              ;  31.25 kBaud (PA)
45.45_supp = 1                                 ;  45.45 kBaud
93.75_supp = 1                                 ;  93.75 kBaud
187.5_supp = 1                                 ; 187.5  kBaud
500_supp = 1                                   ; 500    kBaud
1.5M_supp = 1                                  ;   1.5  MBaud
3M_supp = 1                                    ;   3    MBaud
6M_supp = 1                                    ;   6    MBaud
12M_supp = 1                                   ;  12    MBaud
;
MaxTsdr_9.6 = 60
MaxTsdr_19.2 = 60
;                                              ;  31.25 kBaud (PA)
MaxTsdr_45.45 = 60
MaxTsdr_93.75 = 60
MaxTsdr_187.5 = 60
MaxTsdr_500 = 100
MaxTsdr_1.5M = 150
MaxTsdr_3M = 250
MaxTsdr_6M = 350
MaxTsdr_12M = 800
;
Redundancy = 0                                 ;no redundant transmission
Repeater_Ctrl_Sig = 1                          ;Plug signal  CNTR-P  TTl-level
24V_Pins = 0                                   ;Plug signals  M24V and P24 V not connected
Implementation_Type = "SPC3"                   ;Application of ASIC SPC3
;
;
;                                              ;*** Slave specific values ***
Freeze_Mode_supp = 0                           ;Freeze-mode is not supported
Sync_Mode_supp = 0                             ;Sync-mode is not supported
Auto_Baud_supp = 1                             ;Automatic recognition of baudrate
Set_Slave_Add_supp = 1                         ;Set_Slave_Add is supported
Min_Slave_Intervall = 6                        ;Slave-Interval  = 0.6 ms
Modular_Station = 1                            ;Modular station
Max_Module = 13
Max_Diag_Data_Len = 6                          ;
Slave_Family = 5                               ;
;
;
;                                              ;*** Parameterization ***
;
;This lines are for locating PBC file, and initial data length.
;Do not disturb!!!
;@PBC_File = C:\APP\JUMO\GSDGEN\14401XX\E\ju_i500.PBC
;@INIT_LEN = 2
;
User_Prm_Data_Len = 52
User_Prm_Data = 0x00, 0x03, 0x06, 0x06, 0x13, 0x00, 0xCE, 0x04, 0x13, 0x00, \
0xD2, 0x04, 0x13, 0x00, 0xD4, 0x04, 0x11, 0x09, 0x9E, 0x02, 0x13, \
0x08, 0x3C, 0x04, 0x11, 0x01, 0x7A, 0x02, 0x23, 0x00, 0xCE, 0x04, \
0x23, 0x08, 0x3C, 0x04, 0x21, 0x01, 0x7A, 0x02, 0x21, 0x01, 0xBB, \
0x02, 0x21, 0x01, 0xBC, 0x02, 0x21, 0x01, 0xBD, 0x02
Max_Input_Len = 21
Max_Output_Len = 16
Max_Data_Len = 37
;==================== Input Master ========================================
Module = "Interface Mode" 0x10
Preset = 1
Endmodule
Module = "ller/Controller1/Actual setpoint" 0x13
Preset = 1
Endmodule
Module = "oller/Controller1/Output heating" 0x13
Preset = 1
Endmodule
Module = "oller/Controller1/Output cooling" 0x13
Preset = 1
Endmodule
Module = "Binary/Timersignals 0x099E" 0x11
Preset = 1
Endmodule
Module = "Setpoints/Controller1/Setpoint 1" 0x13
Preset = 1
Endmodule
Module = "Commands/Setpoint switching  R1" 0x11
Preset = 1
Endmodule
;==================== Output Master ========================================
Module = "ller/Controller1/Actual setpoint" 0x23
Preset = 1
Endmodule
Module = "Setpoints/Controller1/Setpoint 1" 0x23
Preset = 1
Endmodule
Module = "Commands/Setpoint switching  R1" 0x21
Preset = 1
Endmodule
Module = "Programstart/Start hour" 0x21
Preset = 1
Endmodule
Module = "Programstart/Start minute" 0x21
Preset = 1
Endmodule
Module = "Programstart/Start second" 0x21
Preset = 1
Endmodule