#Profibus_DP
;
PrmText=1
Text(0) = "no swap (Intel)"
Text(1) = "swap (Motorola)"
EndPrmText
;
PrmText=2
Text(0) = "no I/O bus error check"
Text(1) = "cyclic I/O bus error check"
EndPrmText
;
PrmText=3
Text(0) = "no err. check of sp. fct. blocks"
Text(1) = "err. check of sp. fct. blocks"
EndPrmText
;
ExtUserPrmData = 1 "swap data (Intel/Motorola)"
Bit(0) 0 0-1
Prm_Text_Ref = 1
EndExtUserPrmData
;
ExtUserPrmData = 2 "cyclic status check of I/O units"
Bit(1) 0 0-1
Prm_Text_Ref = 2
EndExtUserPrmData
;
ExtUserPrmData = 3 "err. check of sp. fct. units"
Bit(2) 0 0-1
Prm_Text_Ref = 3
EndExtUserPrmData
;
GSD_Revision        = 2
;
Vendor_Name="Mitsubishi Electric Corp."
Model_Name          = "FX2N-32DP-ID Mitsubishi"
Revision            = "1.0"
Ident_Number        = 0xF232
Protocol_Ident      = 0
Station_Type        = 0
FMS_supp            = 0
Hardware_Release    = "D"
Software_Release    = "1.01"
;
9.6_supp            = 1
19.2_supp           = 1
93.75_supp          = 1
187.5_supp          = 1
500_supp            = 1
1.5M_supp           = 1
3M_supp             = 1
6M_supp             = 1
12M_supp            = 1
;
MaxTsdr_9.6         = 60
MaxTsdr_19.2        = 60
MaxTsdr_93.75       = 60
MaxTsdr_187.5       = 60
MaxTsdr_500         = 100
MaxTsdr_1.5M        = 150
MaxTsdr_3M          = 250
MaxTsdr_6M          = 450
MaxTsdr_12M         = 800
;
Redundancy=0
Repeater_Ctrl_Sig   = 2
24V_Pins            = 0
Implementation_Type="spc3"
Bitmap_Device       = "FX2N32_N"
Bitmap_Diag         = "FX2N32_D"
Bitmap_SF           = "FX2N32_S"
;
Freeze_Mode_supp    = 1
Sync_Mode_supp      = 1
Auto_Baud_supp      = 1
Set_Slave_Add_supp  = 0
;User_Prm_Data_Len   = 0                          	
Min_Slave_Intervall = 1
;
Modular_Station     = 0
;Modul_Offset        = 0
Max_User_Prm_Data_Len = 200
;
Fail_Safe           = 0
Slave_Family	 = 3
Max_Diag_Data_Len   = 15
;
;ERROR MESSAGES
;BFM 8029 bit settings
Unit_Diag_Bit(0)		=	"general error"
Unit_Diag_Bit(2)		=	"power failure"
Unit_Diag_Bit(6)		=	"I/O bus error"
Unit_Diag_Bit(7)		=	"from/to error"
Unit_Diag_Bit(10)	=	"config. error"
Unit_Diag_Bit(11)	=	"param. error"
Unit_Diag_Bit(15)	=	"run/stop flag"
;
Ext_User_Prm_Data_Const(0)= 0x00,0x00
Ext_User_Prm_Data_Ref(1) = 1
Ext_User_Prm_Data_Ref(1) = 2
Ext_User_Prm_Data_Ref(1) = 3
;
Module = "8 bit input" 0x10,0x10,0x20,0x20
EndModule